Piping Identification Number:	Piping Location:	Project ID

Introduction

Executive Summary

Does equipment meet acceptance Criteria or Require Level 2 Inspection?

YesNo

DESCRIPTION OF SUGGESTED FOLLOW UP INSPECTION

Design Data (Obtained From Drawings/Name Plate):

MAWP.
MAWP.
Design Pressure / Temp.
Size
Design Code
Pipe Service:

EXTERNAL OBSERVATIONS:

1.0 Straight Pipe Runs, Expansion Joints, Elbows, Reducers and Tees, including where Pipe Rests on Supports:

S/N	Piping Components	Observations	Observation Images
1.1.1	Inspect for signs of leakage, mechanical damage, sagging, coating failure, corrosion, cracks in welds and excessive vibration.
1.1.2	Inspect point at which the pipe lay on supports for corrosion under pipe supports.
1.1.3	Inspect for misalignment that may be indicated by piping dislodged from one or more supports, excessively deformed expansion joints, out of plumb, etc.

1.2. Branch Connections, Including Reinforcement Pad

S/N	Piping Components	Observations	Observation Images
1.2.1	Inspect for signs of leakage, mechanical damage, distortion, coating failure, corrosion, cracks in fillet welds.
1.2.2	Inspect for signs of leakage from weep holes of reinforcement pads if applicable.

1.3. Small Piping Takeoffs (Valves and Piping) Including Gussets

S/N	Piping Components	Observations	Observation Images
1.3.1	Inspect for signs of leakage, mechanical damage, distortion, coating failure, corrosion, cracks in fillet welds.
1.3.2	Inspect for proper gusseting and seal welding of threaded connections.

1.4: Flanges and Associated Hardware

S/N	Piping Components	Observations	Observation Images
1.4.1	Inspect for signs of leakage and for full stud thread engagement
1.4.2	Inspect for coating failure, corrosion on studs, nuts and in between the flange faces
1.4.3	Inspect for cracks in studs and welds.

1.5. Insulation/Weatherproofing/Jacketing:

S/N	Piping Components	Observations	Observation Images
1.5.1	Check for any corrosion damage

1.6. Dead Legs

S/N	Piping Components	Observations	Observation Images
1.6.1	Inspect for signs of leakage, mechanical damage, distortion, coating failure, corrosion, and cracks in welds.

1.7. Filter, Strainer, etc:

S/N	Piping Components	Observations	Observation Images
1.7.1	Inspect for signs of leakage, mechanical damage, coating failure, corrosion or cracks in welds
1.7.2	Verify that the device is properly supported to prevent excessive loading on piping.

1.8. Anchors/Restraints/Guides/Spring Hangers / Support Roods Including Pipe Clamps

S/N	Piping Components	Observations	Observation Images
1.8.1	Inspect for mechanical damage, cracks in attachment welds, corrosion and distortion
1.8.2	Verity that spring hangers are free to move and not bottomed or topped out of their travel range.
1.8.3	Note any missing hangers or supports.

S/N	Piping Components	Observations	Observation Images
1.9.1	Inspect for signs of leakage especially from weep holes.
1.9.2	Inspect for mechanical damage and cracks in the welds attaching it to the process piping
1.9.3	Inspect for coating failure and corrosion especially on hard to reach areas that may not have been properly coated.
1.9.4	Verify that dummy legs have unobstructed weep holes at the bottom
1.9.5	Inspect internal of open ended supports and underside of process piping through the open end for corrosion

2.0 . Safety Relief Device and Associated Piping

S/N	Piping Components	Observations	Observation Images
2.1.1	Verify that the inlet and outlet block valves are carsealed open
2.1.2	Verify that atmospheric vents have weep holes and are free of obstructions
2.1.3	Identify inlet, outlet and vent piping that have low points that could trap liquids.

2.2. Thermowells and Temperature Indicating Instruments:

S/N	Piping Components	Observations	Observation Images
2.2.1	Inspect for signs of leakage, mechanical damage, improper installation, corrosion and or cracks in attachment welds.
2.2.2	Inspect for presence of seal welds.

2.3. Temporary Repair Clamps/Enclosures

S/N	Piping Components	Observations	Observation Images
2.3.1	Inspect for leakage, mechanical damage, paint failure, corrosion or cracks in welds

2.4. Temporary Repair Clamps/Enclosures

S/N	Piping Components	Observations	Observation Images
2.4.1	Inspect for leakage, mechanical damage, paint failure, corrosion or cracks in welds

Save